Landing Gear

 Landing Gear


   Airplanes require landing gear for taxiing, takeoff, and landing. The earliest airplane of all--the Wright Flyer--used skids as its landing gear. Soon, wheels were attached to the skids. Since that time, various arrangements have been used for wheels and structures to connect them to the airplane. Today, there are three common types of landing gear: conventional, tricycle, and tandem (see figure 1-8).

   Conventional landing gear consists of two wheels forward of the aircraft's center of gravity and a third small wheel at the tail. This type of landing gear is most often seen in older general aviation airplanes. The two main wheels are fastened to the fuselage by struts. Without a wheel at the nose of the plane, it easily pitches over if brakes are applied too soon. Because the tailwheel is castered--free to move in any direction--the plane is very difficult to control when landing or taking off.
   The tricycle landing gear, as you can guess from its name, has three wheels--two main wheels and a nosewheel (see figure 1-9). This type of landing gear makes the aircraft easier to handle on the ground and it also makes landings much safer. An aircraft equipped with tricycle landing gear is less apt to pitch forward.
   The tandem landing gear is used for very large aircraft like the B-52 bomber and the U-2 reconnaissance/research aircraft. The main landing gear is in two sets that are located one behind the other on the fuselage. The tandem landing gear allows the use of a highly flexible wing, but it may also require the use of small wheels on the tips of the wings to keep the wings from scraping the ground.

Go to first page….

Thanks you for showing interest  towards learn about Airplanes….You are not a common man now ! For any query comment your question here and for contect me mail me at faiyazpatel555@gmail.com.




Comments

Post a Comment

Popular posts from this blog

Empennage

Image
Empennage     The empennage, commonly called the tail assembly (see figure 1-7), is the rear section of the body of the airplane. Its main purpose is to give stability to the aircraft.  The fixed parts are the horizontal stabilizer and the vertical stabilizer or fin. The front, fixed section is called the  horizontal stabilizer  and is used to p revent the airplane from pitching up or down .   The rear section is called the  elevator  and is usually hinged to the horizontal stabilizer. The elevator is a movable airfoil that  controls the up-and-down motion of the aircraft's nose.    The vertical tail structure is divided into the  vertical stabilizer and the rudder . The front section is called the  vertical stabilizer and is used to prevent the aircraft from yawing back and forth .  The principle behind its operation is much like the principle of a deep keel on a sailboat. In light, single-engine aircraft, it also serves to offset the tendency of the air
Read more

Top 10 Best Aeronautical Engineering Colleges in The World - 2018

Image
Aeronautical engineering involves the study of aircrafts and spacecraft’s. This course prepares the Top 10 Richest students to design and engineer flight-capable.    This course has a vast scope for employment. Many universities have included this course in their schools to equip the enrolling students with sufficient knowledge and prepare them to serve the field of science. This course is the passport to the future because of the various developments happening in this space and in aerodynamic research. Here is the list of top universities which have successfully made use of the room available for developed to offer quality education. Students from all over the world are competing to get an admission in these universities. They are becoming their better selves every day to become worthy of selection by these universities. Students aspiring to become a good aeronautical engineer will have these universities set as their goals and in their wish list. Below are the Top 1
Read more

Power Plant

Image
 Power Plant    The power plant may be an engine and propeller combination or a jet engine. The most commonly used power plant in personal aircraft is the gasoline engine, which will be studied in detail later in this chapter. It is mounted in position against a fire wall in the front section of the airplane. The fire wall provides separation of the power plant from the remainder of the fuselage. The engine cowling is the metal covering which encases the engine and its accessories, streamlining the plane and conducting air around the engine cylinders for cooling. Because the action of the pistons is an up-and-down movement, this engine is called a reciprocating engine or a piston engine. In multiengine aircraft, the engines are usually mounted on the leading edges of the wings.   The jet engine gives the airplane a thrust (push forward) because of the jet exhaust gas coming out of the back of the engine. The moving part of this engine is a turbine. Jet engines may be mounte
Read more